Close filters
 
  •  
  •  
  •  
from to
1 From 2
No results were found for the filter!
Wavy Joint System Tap
Wavy Joint System Tap
Tap, tap, tap. That sound you hear is the sound of the future in threaded cue pins. The WavyTap is the first design improvement for joining the two parts of the cue together in years. The WAVY Joint System gives you better contact to the...
€499.90 *
3/8-10 Special 101,6mm (4") Long Tap
3/8-10 Special 101,6mm (4") Long Tap
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 6.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€49.95 *
3/8-11 x HO Special 101,6mm (4") Long Tap - Zero Limit
3/8-11 x HO Special 101,6mm (4") Long Tap -...
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 4.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€55.95 *
3/8-10 x HO Special 101,6mm (4") Long Tap - Zero Limit
3/8-10 x HO Special 101,6mm (4") Long Tap -...
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 4.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€54.75 *
7/16-20 Plug Tap for self aligning Insert
7/16-20 Plug Tap for self aligning Insert
Atlas high speed steel standard insert taps. These are 3.00” short taps for use in the installation of brass shaft inserts. Please note that the 7/16-14 tap is for all standard brass inserts; the 7/16-20 tap is to be used for...
€30.60 *
3/8-10 Special 101,6mm (4") Long Tap
3/8-10 Special 101,6mm (4") Long Tap
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 4.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€45.25 *
7/16-14 Plug Tap for standard Insert
7/16-14 Plug Tap for standard Insert
Atlas high speed steel standard insert taps. These are 3.00” short taps for use in the installation of brass shaft inserts. Please note that the 7/16-14 tap is for all standard brass inserts; the 7/16-20 tap is to be used for...
€26.95 *
7/16-11 x 101,6mm (4") Long Tap
7/16-11 x 101,6mm (4") Long Tap
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 4.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€53.55 *
5/16-18 Special 101,6mm (4") Long Tap
5/16-18 Special 101,6mm (4") Long Tap
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 4.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€54.75 *
5/16-14 Special 101,6mm (4") Long Tap
5/16-14 Special 101,6mm (4") Long Tap
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 4.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€54.75 *
Joint Tenon Compression Die
Joint Tenon Compression Die
5/8-11
€32.90 *
3/8-14 x Special 101,6mm (4") Long Tap
3/8-14 x Special 101,6mm (4") Long Tap
Atlas high speed steel, special extra long taps are specifically designed for custom cue makers. All taps are 4.00” in length with a shank smaller than the thread pitch diameter enabling you to tap to maximum depth.
€46.40 *
1 From 2
Viewed